 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| (R) ISL28271, ISL28272 Data Sheet August 17, 2007 FN6390.2 Dual Micropower, Single Supply, Rail-toRail Input and Output (RRIO) Instrumentation Amplifier The ISL28271 and ISL28272 are dual micropower instrumentation amplifiers (in-amps) optimized for single supply operation over the +2.4V to +5.5V range. Both devices feature an Input Range Enhancement Circuit (IREC) which maintains CMRR performance for input voltages equal to the positive and negative supply rails. The input signal is capable of swinging 10% above the positive supply rail and to 100mV below the negative supply with only a slight degradation of the CMRR performance. The output operation is rail-to-rail. The ISL28271 is compensated for a minimum gain of 10 or more. For higher gain applications, the ISL28272 is compensated for a minimum gain of 100. The in-amps have CMOS input devices for maximum input common voltage range. The amplifiers can be operated from one lithium cell or two Ni-Cd batteries. Features * 120A typical supply current for both channels * 30pA max input bias current * 100dB CMRR, PSRR * 0.7V/C offset voltage temperature coefficient * 180kHz 3dB Bandwidth - ISL28271 * 100kHz 3dB Bandwidth - ISL28272 * 0.5V/s slew rate * Single supply operation * Rail-to-rail input and output (RRIO) * Input is capable of swinging above V+ and below V(ground sensing) * 0.081%1 typical gain error - ISL28271 * -0.19%1 typical gain error - ISL28272 * Pb-free available (RoHS compliant) Ordering Information PART NUMBER (Note) ISL28271FAZ* ISL28272FAZ* ISL28271INEVAL1Z ISL28272INEVAL1Z PART MARKING 28271 FAZ 28272 FAZ PACKAGE (Pb-free) PKG. DWG. # Applications * Battery- or solar-powered systems * Strain gauge * Sensor signal conditioning * Medical devices * Industrial instrumentations 16 Ld QSOP MDP0040 16 Ld QSOP MDP0040 Evaluation Platform Evaluation Platform *Add "-T7" suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Related Literature * AN1290, ISL2827xINEVAL1Z Evaluation Board User's Guide * AN1298, Instrumentation Amplifier Application Note Pinout ISL28271, ISL28272 (16 LD QSOP) TOP VIEW NC 1 OUT_A 2 FB+_A 3 FB-_A 4 IN-_A 5 IN+_A 6 EN_A 7 V- 8 +-+ 16 V+ 15 OUT_B 14 FB+_B 13 FB-_B 12 IN-_B 11 IN+_B 10 EN_B 9 NC 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2006, 2007. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL28271, ISL28272 Absolute Maximum Ratings (TA = +25C) Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V Supply Turn-on Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . 1V/s Input Current (IN, FB) ISL28272 . . . . . . . . . . . . . . . . . . . . . . . . 5mA Differential Input Voltage (IN, FB) ISL28272 . . . . . . . . . . . . . . . 0.5V Input Current (IN, FB) ISL28271 . . . . . . . . . . . . . . . . . . . . . . . . 5mA Differential Input (IN, FB) Voltage ISL28271 . . . . . . . . . . . . . . . 1.0V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . V- - 0.5V to V+ + 0.5V ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V Thermal Information Thermal Resistance JA (C/W) 16 Ld QSOP Package . . . . . . . . . . . . . . . . . . . . . . . 112 Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . .Indefinite Ambient Operating Temperature Range . . . . . . . . .-40C to +125C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65C to +150C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . +125C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +125C. CONDITIONS ISL28271 ISL28272 MIN (Note 1) -600 -1200 -500 -750 TYP 35 35 PARAMETER VOS DESCRIPTION Input Offset Voltage MAX (Note 1) 600 1200 500 750 UNIT V V V/C TCVOS IOS IB eN Input Offset Voltage Temperature Coefficient -40C to +125C Input Offset Current between IN+ and IN-, and between FB+ and FBInput Bias Current (IN+, IN-, FB+, and FB- terminals) Input Noise Voltage See graphs for extended temperature range -40C to +85C See graphs for extended temperature range -40C to +85C ISL28271 ISL28272 Input Noise Voltage Density ISL28271 ISL28272 fo = 1kHz f = 0.1Hz to 10Hz -30 -80 -30 -80 0.7 5 10 10 6 240 78 fo = 1kHz 0.92 0.2 1 V+ = 2.4V to 5.0V ISL28271 ISL28272 VCM = 0V to 5V 0 80 70 80 75 80 75 RL = 100k to 2.5V 100 100 100 +0.081 -0.19 V+ 30 80 30 80 pA pA VP-P VP-P nV/Hz nV/Hz pA/Hz pA/Hz G V dB dB dB % iN Input Noise Current Density ISL28271 ISL28272 RIN VIN CMRR Input Resistance Input Voltage Range Common Mode Rejection Ratio PSRR EG Power Supply Rejection Ratio Gain Error V+ = 2.4V to 5V ISL28271 ISL28272 2 FN6390.2 August 17, 2007 ISL28271, ISL28272 Electrical Specifications V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +125C. (Continued) CONDITIONS Output low, RL = 100k Output low, RL = 1k Output high, RL = 100k Output high, RL = 1k SR -3db BW Slew Rate -3dB Bandwidth RL = 1k to GND RL = 10k ISL28271 ISL28272 IS,EN IS,DIS VINH VINL IENH IENL VSUPPLY ISC+ ISCNOTE: 1. Parts are 100% tested at +25C. Over temperature limits established by characterization and are not production tested. 2. VSUPPLY = +5.25V max when VENL = +V (device in disable state). Supply Current, Enabled Supply Current, Disabled EN Enable Pin High Level EN Enable Pin Low Level EN Input Current High EN Input Current Low Supply Operating Range Short Circuit Output Current Short Circuit Output Current EN = V+ EN = VV+ to V- (Note 2) V+ = 5V, RL = 10 V+ = 5V, RL = 10 2.4 28 25 24 20 31 26 0.8 26 Both A and B channels enabled, EN = VBoth A and B channels disabled, EN = V+ 2 0.8 1 1.3 50 100 5.5 4.980 4.980 4.85 4.80 0.4 0.35 MIN (Note 1) TYP 3 130 4.99 4.88 0.5 180 100 120 4 156 200 7 9 0.7 0.75 MAX (Note 1) 6 30 175 225 UNIT mV mV V V V/s kHz kHz A A V V A nA V mA mA PARAMETER VOUT DESCRIPTION Maximum Voltage Swing 3 FN6390.2 August 17, 2007 ISL28271, ISL28272 Typical Performance Curves 70 60 50 GAIN (dB) 40 30 20 10 1 10 100 1k 10k 100k 1M FREQUENCY (Hz) GAIN = 1000 GAIN = 500 GAIN = 200 GAIN = 100 GAIN = 50 GAIN = 20 GAIN = 10 40 30 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M GAIN (dB) VCM = 5V VOUT = 10mVP-P RL = 10k V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. 90 GAIN = 10,000 80 GAIN = 5,000 70 60 50 GAIN = 2,000 GAIN = 1,000 GAIN = 500 GAIN = 200 GAIN = 100 VCM = 5V VOUT = 10mVP-P RL = 10k FIGURE 1. ISL28271 FREQUENCY RESPONSE vs CLOSED LOOP GAIN, V+ = VCM = 5V FIGURE 2. ISL28272 FREQUENCY RESPONSE vs CLOSED LOOP GAIN, VCM = V+ 70 60 50 GAIN (dB) 40 30 20 10 GAIN = 1000 GAIN = 500 GAIN = 200 GAIN = 100 GAIN = 50 GAIN = 20 GAIN = 10 VCM = 2.5V VOUT = 10mVP-P RL = 10k GAIN (dB) 90 GAIN = 10,000 80 GAIN = 5,000 70 60 50 40 30 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M GAIN = 2,000 GAIN = 1,000 GAIN = 500 GAIN = 200 GAIN = 100 VCM = 2.5V VOUT = 10mVP-P RL = 10k 1 10 100 1k 10k 100k 1M FREQUENCY (Hz) FIGURE 3. ISL28271 FREQUENCY RESPONSE vs CLOSED LOOP GAIN, V+ = 5V, VCM = 1/2V+ FIGURE 4. ISL28272 FREQUENCY RESPONSE vs CLOSED LOOP GAIN, VCM = 1/2V+ 70 60 50 GAIN (dB) 40 30 20 10 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M GAIN = 1000 GAIN = 500 GAIN = 200 GAIN = 100 GAIN = 50 GAIN = 20 GAIN = 10 VCM = +10mV VOUT = 10mVP-P RL = 10k GAIN (dB) 90 GAIN = 10,000 80 GAIN = 5,000 70 60 50 40 30 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M GAIN = 2,000 GAIN = 1,000 GAIN = 500 GAIN = 200 GAIN = 100 VCM = +10mV VOUT = 10mVP-P RL = 10k FIGURE 5. ISL28271 FREQUENCY RESPONSE vs CLOSED LOOP GAIN, V+ = 5V, VCM = 10mV FIGURE 6. ISL28272 FREQUENCY RESPONSE vs CLOSED LOOP GAIN, VCM = V- 4 FN6390.2 August 17, 2007 ISL28271, ISL28272 Typical Performance Curves 25 V+ = 5V V+ = 2.4V V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. 45 40 35 30 GAIN (dB) 25 20 15 10 5 0 AV = 100 RL = 10k CL = 10pF RF/RG = 100 RF = 10k RG = 100 10 100 1k 10k 100k 1M FREQUENCY (Hz) V+ = 2.4V V+ = 5V 20 GAIN (dB) 15 10 AV = 10 RL = 10k CL = 10pF 5 RF/RG = 10 RF = 1k RG = 100 0 10 100 1k 10k 100k 1M FREQUENCY (Hz) FIGURE 7. ISL28271 FREQUENCY RESPONSE vs SUPPLY VOLTAGE FIGURE 8. ISL28272 FREQUENCY RESPONSE vs SUPPLY VOLTAGE 25 820pF 20 470pF 50 2200pF 1200pF GAIN (dB) 45 GAIN (dB) 15 AV = 10 R = 10k CL = 10pF RF/RG = 10 RF = 1k RG = 100 10 100 1k 10k 220pF 100pF 40 820pF AV = 100 R = 10k CL = 10pF RF/RG = 100 RF = 10k RG = 100 10 100 1k 10k 100k FREQUENCY (Hz) 35 10 56pF 30 5 25 100k 1M FREQUENCY (Hz) 1M FIGURE 9. ISL28271 FREQUENCY RESPONSE vs CLOAD FIGURE 10. ISL28272 FREQUENCY RESPONSE vs CLOAD 90 80 70 60 CMRR (dB) 50 40 30 20 10 0 -10 10 100 1k 10k 100k 1M AV = 10 CMRR (dB) 120 100 80 60 AV = 100 40 20 0 10 100 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 11. ISL28271 CMRR vs FREQUENCY FIGURE 12. ISL28272 CMRR vs FREQUENCY 5 FN6390.2 August 17, 2007 ISL28271, ISL28272 Typical Performance Curves 120 100 80 PSRR (dB) 60 V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. 120 100 PSRR+ PSRR (dB) 80 PSRR+ 60 40 AV = 100 20 0 10 PSRR- PSRR40 AV = 10 20 0 10 100 1k 10k 100k 1M 100 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 13. ISL28271 PSRR vs FREQUENCY FIGURE 14. ISL28272 PSRR vs FREQUENCY 1400 INPUT VOLTAGE NOISE (nV/Hz) INPUT VOLTAGE NOISE (nV/Hz) 1200 1000 800 600 AV = 10 400 200 0 1 700 600 500 400 300 200 100 0 10 100 1k 10k 100k FREQUENCY (Hz) AV = 100 1 10 100 1k 10k 100k FREQUENCY (Hz) FIGURE 15. ISL28271 INPUT VOLTAGE NOISE SPECTRAL DENSITY FIGURE 16. ISL28272 INPUT VOLTAGE NOISE SPECTRAL DENSITY 6 CURRENT NOISE (pA/Hz) CURRENT NOISE (pA/Hz) 5 4 3 2 1 0 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 1 10 100 1k 10k 100k FREQUENCY (Hz) 1 10 100 1k 10k 100k AV = 100 AV = 10 FREQUENCY (Hz) FIGURE 17. ISL28271 INPUT CURRENT NOISE SPECTRAL DENSITY FIGURE 18. ISL28272 INPUT CURRENT NOISE SPECTRAL DENSITY 6 FN6390.2 August 17, 2007 ISL28271, ISL28272 Typical Performance Curves V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. VOLTAGE NOISE (5V/DIV) TIME (1s/DIV) VOLTAGE NOISE (2V/DIV) TIME (1s/DIV) FIGURE 19. ISL28271 0.1Hz TO 10Hz INPUT VOLTAGE NOISE, GAIN = 10 FIGURE 20. ISL28272 0.1Hz TO 10Hz INPUT VOLTAGE NOISE, GAIN = 100 160 190 n = 3000 SUPPLY CURRENT (A) 170 150 130 110 MIN 90 70 50 -40 -20 0 20 40 60 80 100 120 MEDIAN n = 3000 MAX SUPPLY CURRENT (A) 150 140 130 MEDIAN 120 110 100 90 -40 MIN MAX -20 0 20 40 60 80 100 120 TEMPERATURE (C) TEMPERATURE (C) FIGURE 21. ISL28271 SUPPLY CURRENT ENABLED vs TEMPERATURE, V+, V- = 2.5V, VIN = 0V FIGURE 22. ISL28272 SUPPLY CURRENT ENABLED vs TEMPERATURE, V+, V- = 2.5V, VIN = 0V 5.0 n = 3000 SUPPLY CURRENT (A) 4.5 MAX 7 n = 3000 6 SUPPLY CURRENT (A) 5 4 3 MEDIAN 2 1 0 -40 MIN MAX 4.0 MEDIAN 3.5 3.0 MIN 2.5 -40 -20 0 20 40 60 80 100 120 -20 0 TEMPERATURE (C) 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 23. ISL28271 SUPPLY CURRENT DISABLED vs TEMPERATURE, V+, V- = 2.5V, VIN = 0V FIGURE 24. ISL28272 SUPPLY CURRENT DISABLED vs TEMPERATURE, V+, V- = 2.5V, VIN = 0V 7 FN6390.2 August 17, 2007 ISL28271, ISL28272 Typical Performance Curves 160 150 170 140 CMRR (dB) 130 120 110 100 90 80 70 -40 -20 0 20 40 60 80 100 120 70 -40 -20 0 20 40 60 80 100 120 MIN MEDIAN MAX CMRR (dB) 150 130 MEDIAN 110 90 MIN MAX n = 3000 V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. 190 n = 3000 TEMPERATURE (C) TEMPERATURE (C) FIGURE 25. ISL28271 CMRR vs TEMPERATURE, VCM = +2.5V TO -2.5V FIGURE 26. ISL28272 CMRR vs TEMPERATURE, VCM = +2.5V TO -2.5V 150 140 130 PSRR (dB) MAX 180 n = 3000 160 140 120 MEDIAN 100 80 MIN -20 0 20 40 60 80 100 120 60 -40 -20 0 20 MIN 40 60 80 100 120 n = 3000 MAX 110 100 90 80 70 60 -40 MEDIAN TEMPERATURE (C) PSRR (dB) 120 TEMPERATURE (C) FIGURE 27. ISL28271 PSRR vs TEMPERATURE, V+, V- = 1.2V TO 2.5V FIGURE 28. ISL28272 PSRR vs TEMPERATURE, V+, V- = 1.2V TO 2.5V 4.91 n = 3000 4.90 MAX 4.89 VOUT (V) VOUT (V) 4.88 4.87 4.86 MIN 4.85 4.84 -40 MEDIAN 4.91 n = 3000 4.90 MAX 4.89 4.88 4.87 4.86 4.85 4.84 -40 MEDIAN MIN -20 0 20 40 60 80 100 120 -20 0 20 40 60 80 100 120 TEMPERATURE (C) TEMPERATURE (C) FIGURE 29. ISL28271 VOUT HIGH vs TEMPERATURE, RL = 1k, V+, V- = 2.5V FIGURE 30. ISL28272 VOUT HIGH vs TEMPERATURE, RL = 1k, V+, V- = 2.5V 8 FN6390.2 August 17, 2007 ISL28271, ISL28272 Typical Performance Curves 4.9980 4.9975 4.9970 VOUT (V) 4.9965 4.9960 4.9955 4.9950 -40 MIN n = 3000 MEDIAN VOUT (V) MAX 4.9975 4.9970 4.9965 4.9960 4.9955 4.9950 -40 MIN V+ = +5V, V- = GND, VFB+ = 1/2V+, RL = Open, TA = +25C, unless otherwise specified. 4.9980 n = 3000 MEDIAN MAX -20 0 20 40 60 80 TEMPERATURE (C) 100 120 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 31. ISL28271 VOUT HIGH vs TEMPERATURE, RL = 100k, V+, V- = 2.5V FIGURE 32. ISL28272 VOUT HIGH vs TEMPERATURE, RL = 100k, V+, V- = 2.5V 170 n = 3000 160 150 VOUT (mV) 140 130 120 110 100 90 -40 -20 0 20 40 60 80 100 120 MIN MEDIAN VOUT (mV) MAX 180 170 160 150 140 130 120 110 100 90 80 -40 -20 0 20 40 60 80 100 120 MIN MEDIAN n = 3000 MAX TEMPERATURE (C) TEMPERATURE (C) FIGURE 33. ISL28271 VOUT LOW vs TEMPERATURE, RL = 1k, V+, V- = 2.5V FIGURE 34. ISL28272 VOUT LOW vs TEMPERATURE, RL = 1k, V+, V- = 2.5V 6.0 5.8 5.6 5.4 VOUT (mV) 5.2 5.0 4.8 4.6 4.4 4.2 4.0 -40 -20 0 20 40 60 80 100 120 MIN MEDIAN VOUT (mV) n = 3000 MAX 6.0 5.8 5.6 5.4 5.2 5.0 4.8 4.6 4.4 4.2 4.0 -40 -20 0 20 40 60 80 100 120 MIN MEDIAN n = 3000 MAX TEMPERATURE (C) TEMPERATURE (C) FIGURE 35. ISL28271 VOUT LOW vs TEMPERATURE, RL = 100k, V+, V- = 2.5V FIGURE 36. ISL28272 VOUT LOW vs TEMPERATURE, RL = 100k, V+, V- = 2.5V 9 FN6390.2 August 17, 2007 ISL28271, ISL28272 Pin Descriptions ISL28271 16 Ld QSOP 2, 15 ISL28272 16 Ld QSOP 2, 15 PIN NAME OUT_A, OUT_B FB+_A, FB+_B EQUIVALENT CIRCUIT Circuit 3 PIN FUNCTION Output Voltage. A complementary Class AB common-source output stage drives the output of each channel. When disabled, the outputs are in a high impedance state. Positive Feedback high impedance terminals. ISL28272 input circuit is shown in Circuit 1A, and the ISL28271 input circuit is shown in Circuit 1B. ISL28271: to avoid offset drift, it is recommended that the terminals of the ISL28271 are not overdriven beyond 1V and the input current must never exceed 5mA. 4, 13 4, 13 FB-_A, FB-_B Circuit 1A, Circuit 1B Negative Feedback high impedance terminals. The FB- pins connect to an external resistor divider to individually set the desired gain of the in-amp. ISL28272 input circuit is shown in Circuit 1A, and the ISL28271 input circuit is shown in Circuit 1B. ISL28271: to avoid offset drift, it is recommended that the terminals of the ISL28271 are not overdriven beyond 1V and the input current must never exceed 5mA. 5, 12 5, 12 IN-_A, IN-_B Circuit 1A, Circuit 1B High impedance Inverting input terminals. Connect to the low side of the input source signal. ISL28272 input circuit is shown in Circuit 1A, and the ISL28271 input circuit is shown in Circuit 1B. ISL28271: to avoid offset drift, it is recommended that the terminals of the ISL28271 are not overdriven beyond 1V and the input current must never exceed 5mA. 6, 11 6, 11 IN+_A, IN+_B Circuit 1A, Circuit 1B High impedance Non-inverting input terminals. Connect to the high side of the input source signal. ISL28272 input circuit is shown in Circuit 1A, and the ISL28271 input circuit is shown in Circuit 1B. ISL28271: to avoid offset drift, it is recommended that the terminals of the ISL28271 are not overdriven beyond 1V and the input current must never exceed 5mA. 7, 10 7, 10 EN_A, EN_B V+ VNC Circuit 2 Active LOW logic pins. When pulled above 2V, the corresponding channel turns off and OUT is high impedance. A channel is enabled when pulled below 0.8V. Built-in pull downs define each EN pin LOW when left floating. Positive Supply terminal shared by all channels. Negative Supply terminal shared by all channels. Grounded for single supply operation. No Connect, pins can be left floating or grounded. V+ LOGIC PIN VCIRCUIT 2 V+ INFBIN+ FB+ VCIRCUIT 3 3, 14 3, 14 Circuit 1A, Circuit 1B 16 8 1, 9 16 8 1, 9 Circuit 4 Circuit 4 V+ INFBIN+ FB+ V- V+ OUT V- V+ CAPACITIVELY COUPLED ESD CLAMP VCIRCUIT 4 CIRCUIT 1A CIRCUIT 1B 10 FN6390.2 August 17, 2007 ISL28271, ISL28272 Application Information Product Description The ISL28271 and ISL28272 are dual channel micropower instrumentation amplifiers (in-amps) which deliver rail-to-rail input amplification and rail-to-rail output swing. The in-amps also deliver excellent DC and AC specifications while consuming only about 120A for both channels. Because the independent pair of feedback terminals set the gain and adjust the output zero level, the ISL28271 and ISL28272 achieve high CMRR regardless of the tolerance of the gain setting resistors. The ISL28271 is internally compensated for a minimum gain of 10. The ISL28272 is internally compensated for a minimum gain of 100. EN pins are available to independently enable or disable a channel. When all channels are off, current consumption is down to typically 4A. performance charts. IREC also cures the abrupt change and even reverse polarity of the input bias current over the whole range of input. Output Stage and Output Voltage Range A Class AB common-source output stage drives the output. The pair of complementary MOSFET devices drive the output VOUT to within a few millivolts of the supply rails. At a 100k load, the PMOS sources current and pulls the output up to 4mV below the positive supply. The NMOS sinks current and pulls the output down to 4mV above the negative supply, or ground in the case of a single supply operation. The current sinking and sourcing capability are internally limited to 31mA. When disabled, the outputs are in a high impedance state. Gain Setting VIN, the potential difference across IN+ and IN-, is replicated (less the input offset voltage) across FB+ and FB-. The function of the in-amp is to maintain the differential voltage across FB- and FB+ equal to IN+ and IN-; (FB- - FB+) = (IN+ - IN-). Consequently, the transfer function can be derived. The in-amp gain is set by two external resistors, the feedback resistor RF, and the gain resistor RG. 2.4V TO 5.5V EN Input Protection All input terminals and feedback terminals have internal ESD protection diodes to both positive and negative supply rails, limiting the input voltage to within one diode beyond the supply rails. Input signals originating from low impedance sources should have current limiting resistors in series with the IN+ and IN- pins to prevent damaging currents during power supply sequencing and other transient conditions. The ISL28272 has additional back-to-back diodes across the input terminals and also across the feedback terminals. If overdriving the inputs is necessary, the external input current must never exceed 5mA. External series resistors may be used as an external protection to limit excessive external voltage and current from damaging the inputs. On the other hand, the ISL28271 has no clamps to limit the differential voltage on the input terminals allowing higher differential input voltages at lower gain applications. It is recommended however, that the terminals of the ISL28271 are not overdriven beyond 1V to avoid offset drift. IN+ IN+ IN- V+ + - EN IN- FB+ FB- VOUT + VISL28271 ISL28272 VCM RG RF Input Stage and Input Voltage Range The input terminals (IN+ and IN-) of the in-amps are a single differential pair of CMOS devices aided by an Input Range Enhancement Circuit, IREC, to increase the headroom of operation of the common-mode input voltage. The feedback terminals (FB+ and FB-) also have a similar topology. As a result, the input common-mode voltage range is rail-to-rail regardless of the feedback terminal settings and regardless of the gain settings. They are able to handle input voltages that are at or slightly beyond the supply and ground sensing making these in-amps well suited for single 5V down to 2.4V supply systems. The IREC enables rail-to-rail input amplification without the problems usually associated with the dual differential stage topology. The IREC ensures that there are no drastic changes in offset voltage over the entire range of the input. See Input Offset Voltage vs Common-Mode Input Voltage in FIGURE 37. GAIN IS SET BY TWO EXTERNAL RESISTORS, RF AND RG VIN = IN+ - INRF VOUT = 1 + ------- VIN R G (EQ. 1) In Figure 37, the FB+ pin and one end of resistor RG are connected to GND. With this configuration, Equation 1 is only true for a positive swing in VIN; negative input swings will be ignored because the output will be at ground. Reference Connection Unlike a three op amp in-amp realization, a finite series resistance seen at the REF terminal does not degrade the high CMRR performance eliminating the need for an additional external buffer amplifier. Figure 38 uses the FB+ pin to provide a high impedance REF terminal. 11 FN6390.2 August 17, 2007 ISL28271, ISL28272 2.4V TO 5.5V EN RF VOUT = 1 + ------- ( VIN ) + ( VREF ) R G (EQ. 4) IN+ IN+ ININ2.9V to 5.5V VCM R1 REF R2 RG FB+ FB+ - V+ EN ISL28271 + VISL28271 ISL28272 VOUT A finite resistance RS in series with the VREF source, adds an output offset of VIN*(RS/RG). As the series resistance RS approaches zero, Equation 3 is simplified to Equation 4 for Figure 39. VOUT is simply shifted by an amount VREF. External Resistor Mismatches Because of the independent pair of feedback terminals provided by the in-amps, the CMRR is not degraded by any resistor mismatches. Hence, unlike a three op amp and especially a two op amp in-amp realization, the ISL28271 and ISL28272 reduce the cost of external components by allowing the use of 1% or more tolerance resistors without sacrificing CMRR performance. The CMRR will be typically 110dB regardless of the tolerance of the resistors used. Instead, a resistor mismatch results in a higher deviation from the theoretical gain - Gain Error. RF FIGURE 38. GAIN SETTING AND REFERENCE CONNECTION . VIN = IN+ - INRF RF VOUT = 1 + ------- ( VIN ) + 1 + ------- ( VREF ) R G R G (EQ. 2) Gain Error and Accuracy The FB+ pin is used as a REF terminal to center or to adjust the output. Because the FB+ pin is a high impedance input, an economical resistor divider can be used to set the voltage at the REF terminal without degrading or affecting the CMRR performance. Any voltage applied to the REF terminal will shift VOUT by VREF times the closed loop gain, which is set by resistors RF and RG. See Figure 38. The FB+ pin can also be connected to the other end of resistor, RG. See Figure 39. Keeping the basic concept that the in-amp maintains constant differential voltage across the input terminals and feedback terminals (FB- - FB+) = (IN+ - IN-), the transfer function of Figure 39 can be derived. 2.4V TO 5.5V EN The gain error indicated in the "Electrical Specifications" table on page 2 is the inherent gain error alone. The gain error specification listed does not include the gain error contributed by the resistors. There is an additional gain error due to the tolerance of the resistors used. The resulting nonideal transfer function effectively becomes: RF VOUT = 1 + ------- x [ 1 ( E RG + E RF + E G ) ] x VIN R G (EQ. 5) Where: ERG = Tolerance of RG ERF = Tolerance of RF EG = Gain Error of the ISL28271 IN+ IN+ IN- V+ + ISL28271 + - EN IN- The term [1 - (ERG +ERF +EG)] is the deviation from the theoretical gain. Thus, (ERG +ERF +EG) is the total gain error. For example, if 1% resistors are used, the total gain error would be: VOUT FB+ FB- TotalGainError = ( E RG + E RF + E G ( typical ) ) TotalGainError = ( 0.01 + 0.01 + 0.005 ) = 2.5% VCM VISL28271 ISL28272 RS RG RF Disable/Power-Down The ISL28271 and ISL28272 have an enable/disable pin for each channel. They can be powered down to reduce the supply current to typically 4A when all channels are off. When disabled, the corresponding output is in a high impedance state. The active low EN pin has an internal pull down and hence can be left floating and the in-amp enabled by default. When the EN is connected to an external logic, the in-amp will shutdown when EN pin is pulled above 2V, and will power up when EN bar is pulled below 0.8V. VREF FIGURE 39. REFERENCE CONNECTION WITH AN AVAILABLE VREF VIN = IN+ - INRS + RF VOUT = 1 + --------------------- + VREF RG (EQ. 3) 12 FN6390.2 August 17, 2007 ISL28271, ISL28272 Unused Channels The ISL28271 and ISL28272 are Dual channel op amps. If the application only requires one channel when using the ISL28271 or ISL28272, the user must configure the unused channel to prevent it from oscillating. The unused channel will oscillate if the input and output pins are floating. This will result in higher than expected supply currents and possible noise injection into the channel being used. The proper way to prevent this oscillation is to configure the feedback pins (FB+, FB-) with the minimum gain stable values for the amplifier with RF and RG resistors and tieing the input terminals to ground (as shown in Figure 40). IN+ IN- + - FB+ FB- + RF RG FIGURE 40. PREVENTING OSCILLATIONS IN UNUSED CHANNELS 13 FN6390.2 August 17, 2007 ISL28271, ISL28272 Quarter Size Outline Plastic Packages Family (QSOP) A D N (N/2)+1 MDP0040 QUARTER SIZE OUTLINE PLASTIC PACKAGES FAMILY INCHES SYMBOL QSOP16 QSOP24 QSOP28 TOLERANCE NOTES PIN #1 I.D. MARK A A1 A2 b 0.068 0.006 0.056 0.010 0.008 0.193 0.236 0.154 0.025 0.025 0.041 16 0.068 0.006 0.056 0.010 0.008 0.341 0.236 0.154 0.025 0.025 0.041 24 0.068 0.006 0.056 0.010 0.008 0.390 0.236 0.154 0.025 0.025 0.041 28 Max. 0.002 0.004 0.002 0.001 0.004 0.008 0.004 Basic 0.009 Basic Reference 1, 3 2, 3 Rev. F 2/07 E E1 1 B 0.010 CAB (N/2) c D E e C SEATING PLANE 0.004 C 0.007 CAB b H E1 e L L1 N L1 A c SEE DETAIL "X" NOTES: 1. Plastic or metal protrusions of 0.006" maximum per side are not included. 2. Plastic interlead protrusions of 0.010" maximum per side are not included. 3. Dimensions "D" and "E1" are measured at Datum Plane "H". 4. Dimensioning and tolerancing per ASME Y14.5M-1994. 0.010 A2 GAUGE PLANE L 44 DETAIL X A1 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 FN6390.2 August 17, 2007 |
Price & Availability of ISL28271INEVAL1Z
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |